shrinkages
英
美
(shrinkage 的复数) n. 收缩, 收缩量, 减低
[化] 起皱; 收缩; 收缩量
shrinkage的复数
双语例句
- At a fixed carbonization temperature, the shrinkages of tangential and radial directions were higher than that of axial direction.
在相同炭化温度下，竹材炭化过程中切向和径向的收缩率高于轴向。 - During the solidification of ductile iron, the volume change can be separated into several stages: after molten iron poured, shrinkages occur along with the temperature descent;
球墨铸铁凝固过程中的体积变化可以分成如下几个阶段：浇注后，铁水随温度的下降，发生液态收缩； - The full sintered Y-TZP had excellent mechanical properties, with bending strength of 710 MPa, fracture toughness of 4.77 MPa · m 1/ 2. During full sintering process, the shrinkages of dental crown in different spatial dimensions were equality and uniformity.
完全烧结的陶瓷材料机械性能优良，弯曲强度达到710MPa，断裂韧性达到4.77MPa·m1/2。在完全烧结过程中，各个方向收缩均匀一致。 - Discussion on different sintering shrinkages between laminates composed of powders with different granularity
关于不同粒度粉末层间烧结收缩不同步问题的探讨 - The shrinkages of green bodies in X, Y, Z directions were measured. The results show that under the same pressure, there is no difference of shrinkage in X and Y directions, and does not change with the height.
结果表明，同一压力下，坯体X向和Y向收缩率一致，并且不同高度处的X、Y向收缩率无明显差异。 - The result shows that there are no casting defects, such as shrinkages, blowholes, and slag inclusions and the quality of casting is steady.
生产结果表明，铸件没有气孔、夹砂、夹渣、收缩等铸造缺陷，铸件品质稳定。 - Abstract: introduced is the experience in replacing atmosperic riser with thermal-isolation riser and improving pouring system to eliminate shrinkages.
文摘：介绍了用保温冒口代替大气压力冒口，改进浇注系统解决铸件缩孔问题的经验。 - The research of early age shrinkages of concrete is very important for the solutions of early age cracking of concrete engineering, especially for high performance concrete.
研究早龄期收缩对于解决混凝土工程，尤其是高性能混凝土的早期开裂具有重要意义。 - On the basis of temperature field numeric emulating and combining with dynamic dividing technology of melting pool isolated region, this article used G/ r~ ( 1/ 2) method to predict possible shrinkages and dispersed shrinkages that may appear in solidification process.
在一般铸件温度场数值模拟的基础上，采用G/R~（1/2）法并结合熔池孤立域的动态划分技术对凝固过程中可能出现的缩松缩孔进行了数值模拟； - When the magnesium alloys are welded by TIG or MIG, the metal in the seam will be oxidized acutely. Some defects such as cracks, voids and shrinkages appear.
当镁合金采用钨极氩弧焊、熔化极气体保护焊等焊接方法时，焊缝金属会剧烈氧化，产生气孔、裂纹等缺陷。